Panasonic NCR18650BD is a mid-drain high capacity Li-ion cell in traditional 18650 format. It's rated at 3180mAh and supports discharging at up to 10A.
Tests were done using ZKETECH EBC-A20, which supports up to 20A discharge, 4-wire measurement and is PC-connected.
I've used version 3.0 of my battery holder based on 0.5mm thick pure copper terminals
I've followed all the prescriptions of the IEC61960-2003 standard concerning battery's capacity measurement. Before each discharging cycle each battery was charged at standard current mentioned in its datasheet to charge end voltage (4.2V) (cut-off at 0.1A, which is the lowest supported by EBC-A20). Before each discharging or charging i've held a 1-1.5hrs pause. The environment temperature was 23.5-24.5°C. To be sure in results i've done each test minimum twice (usually 3-4 times). Battery was bought from Queen Battery.
Panasonic NCR18650BD
My cell has the following marking: C CV 7321.
Specifications from Panasonic NCR18650BD datasheet (pdf):
Rated capacity: 2980mAh at 20°C
Minimum capacity: 3030mAh at 25°C
Typical capacity: 3180mAh at 25°C
Nominal voltage: 3.6V
Standard charge current: 0.909A (0.3C)
Max charge current: 1.5A
Charge end voltage: 4.20V
Charge cut-off current: 60.6mA (0.02C) (100mA used)
Max continuous discharge current: 10A
Discharge cut-off voltage: 2.5V
AC impedance at 1KHz: ≤35mΩ
Max weight: 49.5g
The measured weight of my cell is 46.66g. Measured DCIR at 3030mAh was 23.8±1.0mΩ (in fully charged condition).
Panasonic NCR18650BD capacity test results:
At 0.2C or 0.61A NCR18650BD's capacity was a bit higher than declared and it didn't go below 3020mAh all the way up to 10A. The curves look excellent even at 10A. Just a great cell, nothing to add.
Here is the video version of this review
Check out my YouTube channel for batteries, chargers and other stuff reviews.

Tests were done using ZKETECH EBC-A20, which supports up to 20A discharge, 4-wire measurement and is PC-connected.

I've used version 3.0 of my battery holder based on 0.5mm thick pure copper terminals


I've followed all the prescriptions of the IEC61960-2003 standard concerning battery's capacity measurement. Before each discharging cycle each battery was charged at standard current mentioned in its datasheet to charge end voltage (4.2V) (cut-off at 0.1A, which is the lowest supported by EBC-A20). Before each discharging or charging i've held a 1-1.5hrs pause. The environment temperature was 23.5-24.5°C. To be sure in results i've done each test minimum twice (usually 3-4 times). Battery was bought from Queen Battery.
Panasonic NCR18650BD
My cell has the following marking: C CV 7321.

Specifications from Panasonic NCR18650BD datasheet (pdf):
Rated capacity: 2980mAh at 20°C
Minimum capacity: 3030mAh at 25°C
Typical capacity: 3180mAh at 25°C
Nominal voltage: 3.6V
Standard charge current: 0.909A (0.3C)
Max charge current: 1.5A
Charge end voltage: 4.20V
Charge cut-off current: 60.6mA (0.02C) (100mA used)
Max continuous discharge current: 10A
Discharge cut-off voltage: 2.5V
AC impedance at 1KHz: ≤35mΩ
Max weight: 49.5g
The measured weight of my cell is 46.66g. Measured DCIR at 3030mAh was 23.8±1.0mΩ (in fully charged condition).

Panasonic NCR18650BD capacity test results:

Here is the video version of this review
Check out my YouTube channel for batteries, chargers and other stuff reviews.